The compressor is driven by the star-delta control.
Is driven by V-belt-pulley.
With the V-belt tensioning system, the V-belt tension can be directly adjusted with ease.
Space savings are provided by mounting the compressor unit to the air tank.
Have been designed between 5-15 kW power range and 7.5 / 10 / 13 bar operational pressure.
The minimum pressure valve, oil filter, separator and thermostatic mixture valve have been combined on a single block.
The cabinet has been designed according to the optimal operating conditions: Vibration has been minimized using rubber grommets and sealing elements in various locations. Noise has been minimized with the covering of the inner surfaces of the cabinet with inflammable sound insulation. Easy maintenance access has been implemented with a push open-close locking system of the cabinet doors. The discharge of the cooling air to the outside environment silently has been provided with an exit vent.
This screw group, with single-stage and oil spray characteristics, is mounted on the air-oil tank (separator) tank.
Air-oil cooling system is provided with an axial fan integrated into the air-oil cooler.
Hydraulic hoses are used in air-oil circuits, and pneumatic control system circuits use teflon hoses.
By controlling the temperature of the oil in the oil circuit, a thermostatic mixer valve is combined with the separator block to ensure the provision of oil at the most appropriate temperature to the screw block.
The oil filter element is attached to the combined oil filter block with a separator block.
The air filter element has been placed in a plastic filtre casing to enable easy replacement.
The control of the intake air is provided with the microprocessor control unit with the help of a 3/2 way solenoid valve (idle compressor-working load) and an intake control valve mounted on the screw group on the air intake circuit.
The spin-on type separator used to separate the mixture of air-oil in the air-oil circuit, is attached to the combined separator block with the separator block.
With a safety valve set to +1 bar of the compressor operating pressure on the separator block, the air-oil tank is protected against overpressure situations.
The temperature control of the air-oil circulation system is provided by the NTC temperature sensor integrated into the micro processor control unit.
The pressure control of the air system is provided with the micro processor control unit with the pressure transmitter integrated only on the grip side of the air circulation system.
With the integrated oil flow section integrated on the oil return line when the compressor is working the return of the oil draining from the separator back to the screw group can be observed.
The oil level can be monitored with ease with the oil gauge mounted on the air-oil tank.
Optional feature : The air produced to the consumed air is provided with proportional control valve (energy saving and regular operation)
Optional feature : A oil heater system must be able to be integrated to the compressor to prevent the freezing of oil in heavy weather conditions during the winter season.
Optional feature : It must be possible for more than one compressor to be operated from a single control unit (up to 7 compressors) for equal aging or energy saving.
Optional feature : With a remote monitoring system integrated with the compressors, the monitoring of the operation of the compressor can be ensured with a remote connection to the compressor.
Microprocessor Control Unit :
Compressor panel and unit on single panel, 2×16 graphic LCD display, modbus RTU communication protocol / equal aging and remote monitoring with TTL data bus
Monitoring of compressor operation state on compressor screen (Stopped, stopping, starting, motor start, idling, working at load., auto waiting, awaiting confirmation)
Ability to monitor remaining maintenance period (General service duration, oil element replacement duration, air filter replacement duration, oil change duration, separator change duration, motor bearing replacement duration, screw block bearing replacement duration, bearing lubrication duration)
Recording of the last 15 error information provided by the compressor
Language selection option (Turkish+English, Turkish+Russian)
Selection of unit (bar, Psi / ºC , ºF )
Warning messages defined to ensure the required maintenance and control of the compressor (not stopping the compressor) (General service duration, oil element replacement duration, air filter replacement duration, oil change duration, separator change duration, motor bearing replacement duration, screw block bearing replacement duration, bearing lubrication duration)
Critical faults defined to stop for the safety of the compressor: Emergency Stop, Main Motor Thermal Fan Motor Thermal Phase Sequence, Pressure Sensor, Temperature Sensor, Over-Temperature, Over Pressure, Low Temperature, Short-circuit failure
In the event of the microprocessor control system of the compressor giving the same fault (emergency stop, main motor thermal fault, screw temperature high fault) 3 times within 30 minutes, places itself in safety mode by encoding itself (compressor ceases operation and requires Official service intervention)
Changeable user parameters defined for users and ability to password protect this parameters menu
